Envío GRATIS en compras mayores a $699 MXN
Valido hasta el 20 de Abril del 2023
| SoC | Allwinner A20*(ARM Cortex-A7 dual-core, 1GHz, Mali400MP2 GPU) |
| System Memory | 1GB DDR3 DRAM |
| Storage | SD card slot,Extensible with SATA connection (2.5" SATA HDD with 5V) |
| Video output | HDMI,Composite,Extensible with on-board LVDS connector |
| Audio I/O | HDMI,3.5mm stereo jack output,On-board microphone input |
| Connectivity | Gigabit Ethernet |
| USB | 2* USB 2.0 ports,1* OTG micro USB port,1* micro USB for power supply** |
| Expansion | Extensible 26-pin headers,Camera connector,Display connector for LVDS and touch screen |
| Misc. | 3* on-board buttons, (Power, Reset, Uboot key),IR receiver |
| Dimensions | 92mm X 60 mm |
| Weight | 48 g |
- * Allwinner http://www.allwinnertech.com/en/
- ** Se recomienda una fuente de 5V 2A.
CONECTORES
| CON3 | Pin Name | Multiplex Function Select | GPIO |
| Multi 1 | Multi 2 | ||
| Pin 1 | 3.3V1 | VCC-3V3 | |
| Pin 2* | 5.0V1 | VCC-5V | |
| Pin 3 | SDA | TWI2-SDA | PB21 |
| Pin 4* | 5.0V2 | VCC-5V | |
| Pin 5 | SCL | TWI2-SCK | PB20 |
| Pin 6 | GND3 | GND | |
| Pin 7 | IO-GCLK | GPCLK | PI3 |
| Pin 8 | TXD0 | UART3-TX | PH0 |
| Pin 9 | GND1 | GND | |
| Pin10 | RXD0 | UART3-RX | PH1 |
| Pin11 | IO-0 | IO-0(UART2-RX) | PI19 |
| Pin12 | IO-1 | IO-1 | PH2 |
| Pin13 | IO-2 | IO-2(UART2-TX) | PI18 |
| Pin14 | GND4 | GND | |
| Pin15 | IO-3 | IO-3(UART2-CTS) | PI17 |
| Pin16 | IO-4 | IO-4(CAN_TX) | PH20 |
| Pin17 | 3.3V2 | VCC-3V3 | |
| Pin18 | IO-5 | IO-5(CAN_RX) | PH21 |
| Pin19 | SPI-MOSI | SPI0_MOSI | PI12 |
| Pin20 | GND5 | SPI0_GND | |
| Pin21 | SPI-MISO | SPI0-MISO | PI13 |
| Pin22 | IO-6 | IO-6(UART2_RTS) | PI16 |
| Pin23 | SPI-CLK | SPI0_CLK | PI11 |
| Pin24 | SPI-CE0 | SPI0_CS0 | PI10 |
| Pin25 | GND2 | GND | |
| Pin26 | SPI-CE1 | SPI0_CS1 | PI14 |
* Those 5V pins(CON3 Pin2 & CON3 Pin4) are voltage output pins from BananaPi's PMIC(AXP209). They can NOT be power input pins from external power source. Otherwise, it may damage the BPi board.
CON1 (Camera Serial Interface) CON1 is an extensible on-board CSI connector of Banana Pi. It is a 40-pin FPC connector which can connect external camera module with proper signal pin mappings. The pin definitions of CON1 are shown as below.
| CON1 Pin | Pin Name | GPIO |
| CON1 P01 | LINEINL | |
| CON1 P02 | LINEINR | |
| CON1 P03 | VCC-CSI | |
| CON1 P04 | ADC_X1 | |
| CON1 P05 | GND | |
| CON1 P06 | ADC_X2 | |
| CON1 P07 | FMINL | |
| CON1 P08 | ADC_Y1 | |
| CON1 P09 | FMINR | |
| CON1 P10 | ADC_Y2 | |
| CON1 P11 | GND | |
| CON1 P12 | CSI-FLASH | PH17 |
| CON1 P13 | LRADC0 | |
| CON1 P14 | TWI1-SDA | PB19 |
| CON1 P15 | LRADC1 | |
| CON1 P16 | TWI1-SCK | PB18 |
| CON1 P17 | CSI-D0 | PE4 |
| CON1 P18 | CSI0-STBY-EN | PH19 |
| CON1 P19 | CSI0-D1 | PE5 |
| CON1 P20 | CSI-PCLK | PE0 |
| CON1 P21 | CSI-D2 | PE6 |
| CON1 P22 | CSI0-PWR-EN | PH16 |
| CON1 P23 | CSI-D3 | PE7 |
| CON1 P24 | CSI0-MCLK | PE1 |
| CON1 P25 | CSI-D4 | PE8 |
| CON1 P26 | CSI0-RESET# | PH14 |
| CON1 P27 | CSI-D5 | PE9 |
| CON1 P28 | CSI-VSYNC | PE3 |
| CON1 P29 | CSI-D6 | PE10 |
| CON1 P30 | CSI-HSYNC | PE2 |
| CON1 P31 | CSI-D7 | PE11 |
| CON1 P32 | CSI1-STBY-EN | PH18 |
| CON1 P33 | RESET# | |
| CON1 P34 | CSI1-RESET# | PH13 |
| CON1 P35 | CSI-IO0 | PH11 |
| CON1 P36 | HPR | |
| CON1 P37 | HPL | |
| CON1 P38 | IPSOUT | |
| CON1 P39 | GND | |
| CON1 P40 | IPSOUT |
CON2 (LCD display interface) CON2 is an extensible on-board LCD display LVDS connector of Banana Pi. It is a 40-pin FPC connector which can connect external LCD panel (LVDS) and touch screen (I2C) module as well. The pin definitions of CON2 are shown as below.
| CON2 Pin | Pin Name | Multiplex Function Select | GPIO |
| Multi 1 | Multi 2 | ||
| CON2 P01 | IPSOUT(5V output) | ||
| CON2 P02 | TWI3-SDA | PI1 | |
| CON2 P03 | IPSOUT(5V output) | ||
| CON2 P04 | TWI3-SCK | PI0 | |
| CON2 P05 | GND | ||
| CON2 P06 | LCD0-IO0 | PH7 | |
| CON2 P07 | LCDIO-03 | PH12 | |
| CON2 P08 | LCD0-IO1 | PH8 | |
| CON2 P09 | LCD0-D0 | LVDS0-VP0 | PD0 |
| CON2 P10 | PWM0 | PB2 | |
| CON2 P11 | LCD0-D1 | LVDS0-VN0 | PD1 |
| CON2 P12 | LCD0-IO2 | PH9 | |
| CON2 P13 | LCD0-D2 | LVDS0-VP1 | PD2 |
| CON2 P14 | LCD0-DE | PD25 | |
| CON2 P15 | LCD0-D3 | LVDS0-VN1 | PD3 |
| CON2 P16 | LCD0-VSYNC | PD27 | |
| CON2 P17 | LCD0-D4 | LVDS0-VP2 | PD4 |
| CON2 P18 | LCD0-HSYNC | PD26 | |
| CON2 P19 | LCD0-D5 | LVDS0-VN2 | PD5 |
| CON2 P20 | LCD0-CS | PH6 | |
| CON2 P21 | LCD0-D6 | LVDS0-VPC | PD6 |
| CON2 P22 | LCD0-CLK | PD24 | |
| CON2 P23 | LCD0-D7 | LVDS0-VNC | PD7 |
| CON2 P24 | GND | ||
| CON2 P25 | LCD0-D8 | LVDS0-VP3 | PD8 |
| CON2 P26 | LCD0-D23 | PD23 | |
| CON2 P27 | LCD0-D9 | LVDS0-VN3 | PD9 |
| CON2 P28 | LCD0-D22 | PD22 | |
| CON2 P29 | LCD0-D10 | PD10 | |
| CON2 P30 | LCD0-D21 | PD21 | |
| CON2 P31 | LCD0-D11 | PD11 | |
| CON2 P32 | LCD0-D20 | PD20 | |
| CON2 P33 | LCD0-D12 | PD12 | |
| CON2 P34 | LCD0-D19 | PD19 | |
| CON2 P35 | LCD0-D13 | PD13 | |
| CON2 P36 | LCD0-D18 | PD18 | |
| CON2 P37 | LCD0-D14 | PD14 | |
| CON2 P38 | LCD0-D17 | PD17 | |
| CON2 P39 | LCD0-D15 | PD15 | |
| CON2 P40 | LCD0-D16 | PD16 |
J11 (UART) The jumper J11 is the UART interface. For developers of Banana Pi, this is an easy way to get the UART console output to check the system status and log message.
| J11 Pin | Pin Name | Multiplex Function Select | GPIO |
| Multi 1 | Multi 2 | ||
| J11 Pin1 | TXD | UART0-TX | PB22 |
| J11 Pin2 | RXD | UART0-RX | PB23 |
J12 (UART and Power source) The jumper J12 provides the power source including 3.3V and 5V. There is a pair of UART TX/RX signals output here.
| J12 Pin | Pin Name | Multiplex Function Select | GPIO |
| Multi 1 | Multi 2 | ||
| J12 Pin 1 | 5V | ||
| J12 Pin2 | 3.3V | ||
| J12 Pin3 | NC | IO-7 | PH5 |
| J12 Pin4 | RXD | UART7_RX | PI21 |
| J12 Pin5 | NC | IO-8 | PH3 |
| J12 Pin6 | TXD | UART7_TX | PI20 |
| J12 Pin7 | GND | ||
| J12 Pin8 | GND |